Molle ID Pouch internal width dimension

Pipmeister

Private ☆
Jul 5, 2018
3
0
1
#1
The given dimensions for the ID section of the pouch list it as being 9cm wide. However, that doesn’t tell us the actual width of the ID it can hold, allowing for the pouch side stitching.

Can anyone tell me if it could fit an 8cm wide (11cm tall) ID?

Thanks
 

Sandspoor

Master Sergeant ☆☆☆
Feb 2, 2018
1,385
1,676
252
#2
The given dimensions for the ID section of the pouch list it as being 9cm wide. However, that doesn’t tell us the actual width of the ID it can hold, allowing for the pouch side stitching.

Can anyone tell me if it could fit an 8cm wide (11cm tall) ID?

Thanks
This is actually a good question...well, DOES IT?!
 

Rin

MAD CAT
Staff member
MAD CAT
May 15, 2018
851
770
92
#3
The given dimensions for the ID section of the pouch list it as being 9cm wide. However, that doesn’t tell us the actual width of the ID it can hold, allowing for the pouch side stitching.

Can anyone tell me if it could fit an 8cm wide (11cm tall) ID?

Thanks
Hi Pipmeister, welcome to our forum first! Which ID holster do u mean? Do u have the pic of the product?
 

Rin

MAD CAT
Staff member
MAD CAT
May 15, 2018
851
770
92
#4
If it is the
Phone Pouch 09, as u can see the panel for ID card can hold at most 6cm width card, and the total length of the panel is 12.5cm.
1530848199861.png


1530848172463.png
 
Likes: Andy Z.

Pipmeister

Private ☆
Jul 5, 2018
3
0
1
#9
Guys, thanks for the replies but this is not the ID pouch I am talking about. The one I was talking about was the EDC Hammer Throw ID Pouch (Sku TG-ZJT07) https://www.onetigris.com/catalog/product/view/id/49 which states the overall width is 9cm

I'm also wondering what in the internal width is of the ID window pouch is on the ID Holder 09 (sku is TG-ZJT09 ) https://www.onetigris.com/id-holder-09.html says it's overall width is 13cm but it looks wider than just the width of the window part.

As I mentioned earlier, my PowerBoat license is 8cm wide by 11cm tall as has to be show this way round.
Thanks
 

Rin

MAD CAT
Staff member
MAD CAT
May 15, 2018
851
770
92
#10
Guys, thanks for the replies but this is not the ID pouch I am talking about. The one I was talking about was the EDC Hammer Throw ID Pouch (Sku TG-ZJT07) https://www.onetigris.com/catalog/product/view/id/49 which states the overall width is 9cm

I'm also wondering what in the internal width is of the ID window pouch is on the ID Holder 09 (sku is TG-ZJT09 ) https://www.onetigris.com/id-holder-09.html says it's overall width is 13cm but it looks wider than just the width of the window part.

As I mentioned earlier, my PowerBoat license is 8cm wide by 11cm tall as has to be show this way round.
Thanks
Do u have to put the card in the front transparent window Just measured the EDC Hammer Throw ID Pouch (Sku TG-ZJT07) and ID Holder 09 (sku is TG-ZJT09 ) , both of them with 6.5cm width for ID cards, so it is too small for ur PowerBoat license.
 

Pipmeister

Private ☆
Jul 5, 2018
3
0
1
#12
Do u have to put the card in the front transparent window Just measured the EDC Hammer Throw ID Pouch (Sku TG-ZJT07) and ID Holder 09 (sku is TG-ZJT09 ) , both of them with 6.5cm width for ID cards, so it is too small for ur PowerBoat license.
How bizarre is that - the 09 uses a whole inch for stitching - and from the picture it doesn't look like the hammer throw main body has nearly and inch either side of the photo pouch.

Thanks for checking it out, Rin
 

Rin

MAD CAT
Staff member
MAD CAT
May 15, 2018
851
770
92
#13
How bizarre is that - the 09 uses a whole inch for stitching - and from the picture it doesn't look like the hammer throw main body has nearly and inch either side of the photo pouch.

Thanks for checking it out, Rin
U r welcome Private, the stitching for each edges are around 0.4''. because we use nylon line and for the consideration of durable products, we use durable strap for stitching too, making the width of stitching a bit wider than that of cotton lines.
 
Likes: Andy Z.